Jump to content

Welcome To CameraLoops

Take a moment to join and become a member

DPS VIN & PIN Change Service For General Motors Vehicle Modules


Troy
 Share

Recommended Posts

This service is for folks who need to change the VIN and the PIN in a used secondhand General Motors electronic vehicle module, which is not already listed in the downloads section.

I strive to send you a private message with the DPS VIN or PIN change file between 30 minutes to a few hours, depending on your purchasing time and where I am located at the given time.

 

DPS VIN Change Service

You will receive a DPS archive file which can be used to change the VIN in any of these modules listed below.

Supported Global-A 2 or 5 byte seed modules.

IPC: Instrument panel cluster

BCM: Body control module

EBCM: Electronic brake control module
SDM: Sensing diagnostic module (Airbag)

EPS: Electronic power steering

ECC: Electronic Climate Control HVAC

  1. In order to create the DPS VIN change file, you will need to provide the vehicle model name, the year the vehicle was made and the module's SPS utility calibration file.
  2. Click here for the tutorial on how to acquire and identify the module's utility file.
  3. The modules must be Global-A, 2 or 5 byte seed key

 

You can purchase the DPS VIN change file service from the link below.

 

 

DPS PIN Change Service

You will receive a DPS archive file which can be used to change the PIN in any of these modules listed below.

Supported Global-A 2 or 5 byte seed modules.

IPC: Instrument panel cluster

BCM: Body control module

EBCM: Electronic brake control module
SDM: Sensing diagnostic module (Airbag)

  1. In order to create the DPS PIN change file, you will need to provide the vehicle model name, the year the vehicle was made and the module's SPS utility calibration file.
  2. Click here for the tutorial on how to acquire and identify the module's utility file.
  3. The modules must be Global-A, 2 or 5 byte seed key

 

You can purchase the DPS PIN change file service from the link below.

 

 


View full article

Link to comment
Share on other sites

  • 3 weeks later...
On 10/3/2022 at 4:14 AM, justin101714 said:

So we can finally do Denali clusters? Maybe the Escalade ones too? 

 

Yes you can change VIN and PIN in all GM clusters. 

  • Like 1
Link to comment
Share on other sites

  • 1 month later...
On 10/8/2022 at 12:54 PM, Loading60 said:

How I active and change codes in cluster by xml file?

 

 

 

Link to comment
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
On 12/4/2022 at 9:13 PM, dannygn said:

what about tcm modules?

 

Some TCM modules I can do.

 

 

On 12/14/2022 at 5:44 PM, Lenyn Sanchez said:

each file work for all vehicles or i have to get one file for each VIN number

Each file works for that specific GM model vehicle.

Link to comment
Share on other sites

  • 5 weeks later...
31 minutes ago, CATLOS said:

com esse arquivo posso utilizar em outros modelos similares?

The files will work on a specific model vehicle. 

Link to comment
Share on other sites

  • 3 weeks later...
  • 3 weeks later...
2 hours ago, DSLBURB said:

Is this still able to be used on newer versions of Tech Connect/SPS2? I see a lot of tutorials, and screenshots you post have older SPS, just curious if it can still be used 

Yes, it is the same process.

  • Thanks 1
Link to comment
Share on other sites

  • 3 months later...
18 minutes ago, Emmerson Ganyau said:

Hi Troy

Can you get me a dps achive file to change vin in tcm for a 2015 chevrolet captiva 2.2 diesel

 

Hi, It's not possible to change the VIN in the TCM using DPS. That's something I'm still trying to figure out.

Link to comment
Share on other sites

3 minutes ago, Emmerson Ganyau said:

Thanks for the info.

So which dps achive file should I get for changing vin in Ebcm for the same car, Chevrolet captiva 2.2d 2015?

 

I would need to create the file. Tell me the VIN

Link to comment
Share on other sites

Hi Troy.

I was thinking which vin number to give...

I have a car with all its original modules and not starting. Decided to buy all modules from an accident damaged car which was starting but couldn't manage to get the ebcm and tcm. So since you said the tcm vin can't be changed I'm thinking is it possible to change the ecm, cluster and bcm from the donor car to my vin?

I have the rcdlr and transponder as well, from the donor car. Is that going to work.

The car is a 2015 Chevrelot Captiva 2.2d

If it works then I will send my original vin

Link to comment
Share on other sites

  • 11 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




×
×
  • Create New...